iTechGuides is reader-supported. When you buy through links on our site, we may earn an affiliate commission. As an Amazon Associate I earn from qualifying purchases. Learn more
Why is my Blue Yeti so loud? The usual cause is more than one gain control being turned up: the microphone’s rear Gain knob, Windows or macOS input level, and the app’s own processing. Lower the Yeti Gain first, select Cardioid, face the front of the microphone toward you, and test the signal before changing Discord, OBS, Zoom, or Teams.
“Too loud” can describe several different problems. Other people may hear an overly strong microphone signal, a recording may be clipped and distorted, the room may be picked up too clearly, or only your headphones may be loud. The correct fix depends on which signal is excessive.
Key takeaways
- The fastest diagnosis is a short recording in Windows, macOS, or a basic recorder before opening the affected app.
- Lower the original Blue Yeti’s rear Gain knob and the operating system’s Input volume when the recording is clipped or distorted.
- Cardioid is normally the best pickup pattern for one speaker because the mode focuses more strongly on sound arriving from the front.
- The Yeti’s front headphone-volume knob controls monitoring loudness through headphones connected to the microphone, not necessarily the microphone level sent to the computer.
- OBS recommends keeping incoming audio in its green/yellow operating area of approximately −20 to −9 dBFS; red levels above −9 dBFS indicate a risk of clipping.
- If the same distortion occurs in a basic recorder on multiple computers with a known-good cable, hardware failure becomes more likely.
Why is my Blue Yeti so loud?
A Blue Yeti is usually too loud because gain is being added at more than one point in the audio chain. The physical Yeti Gain control, Windows or macOS input level, an individual app’s microphone setting, automatic gain control, compression, and filter makeup gain can all affect the final result.
Free tools Windows power users keep installed
One-click scans. No signup required.
The original Yeti is a sensitive, multi-pattern USB condenser microphone. Logitech specifies three 14 mm condenser capsules, four pickup patterns, 48 kHz/16-bit operation, and a maximum SPL of 120 dB at 0.5% THD and 1 kHz in its official Yeti specifications. A close, loud speaker, reflective room, desk vibration, or speakers playing into the microphone can therefore create a strong or distorted signal even when the microphone is working normally.
Popular on Amazon
- Custom three-capsule array: This professional USB mic produces clear, powerful, broadcast-quality sound for YouTube videos, Twitch game streaming, podcasting, Zoom meetings, music recording and more
- Blue VO!CE software: Elevate your streamings and recordings with clear broadcast vocal sound and entertain your audience with enhanced effects, advanced modulation and HD audio samples
- Four pickup patterns: Flexible cardioid, omni, bidirectional, and stereo pickup patterns allow you to record in ways that would normally require multiple mics, for vocals, instruments and podcasts
- Onboard audio controls: Headphone volume, pattern selection, instant mute, and mic gain put you in charge of every level of the audio recording and streaming process
- Positionable design: Pivot the mic in relation to the sound source to optimize your sound quality thanks to the adjustable desktop stand and track your voice in real time with no-latency monitoring
What does “too loud” mean?
| What you notice | Most likely source | First check |
|---|---|---|
| Other people say your voice is too loud | Yeti Gain, system Input volume, app level, automatic gain, or compression | Record a basic sample, then lower gain at the earliest point that is too high |
| Crackling, crunchiness, or harsh distortion | Clipping before or inside the recording chain | Reduce Yeti Gain and system Input volume; test your loudest expected speech |
| Your headphones are painfully loud | Yeti headphone monitoring or computer output volume | Lower the Yeti’s front headphone-volume knob or output volume |
| The room, fan, keyboard, or speakers are too prominent | Pickup pattern, distance, reflections, or microphone placement | Select Cardioid, move the microphone, and use headphones instead of speakers |
| The microphone is loud only in Discord, OBS, Zoom, Teams, or a browser | Application-specific input level or processing | Select the Yeti explicitly and temporarily disable automatic processing |
| The level suddenly changes between applications | Per-app settings, automatic gain, or exclusive device control | Compare the operating-system test with each app’s microphone test |
Loudness and distortion are not identical. A clean recording can usually be turned down later. Clipped audio has exceeded the available digital level and cannot be fully restored by lowering playback volume. OBS explains the digital ceiling and clipping behavior in its audio mixer and dBFS guidance.
What should I check on the physical Blue Yeti?
Start with the microphone itself before changing software. The original Blue Yeti has a rear Gain knob, a rear pickup-pattern knob, a front Mute button, a front headphone-volume knob, and a USB connection.
- Gain: controls microphone input sensitivity. Lower it when normal speech or loud peaks overload the recording.
- Pickup pattern: selects Cardioid, Bidirectional, Omnidirectional, or Stereo.
- Mute: mutes the microphone. The front button provides a quick status check.
- Headphone volume: changes the level you hear through headphones connected to the Yeti. It does not necessarily reduce the level other people receive.
The Yeti is a side-address microphone. The front—with the Blue logo, Mute button, and headphone control—should face you. Speaking into the top is a common setup mistake; the resulting weak or uneven sound often causes users to raise Gain unnecessarily. The Blue Yeti quick-start guide illustrates the intended orientation.
The Tool Desk
Outbyte Driver Updater FREEFix the driver behind crashes, sound loss and screen glitchesFind Drivers →Outbyte PC Repair FREEClear out junk files and repair common Windows errorsFree Scan →How should I position the Blue Yeti?
For solo speech, select Cardioid, face the front of the microphone toward your mouth, and begin roughly 4–8 inches away. The distance is a starting range rather than a universal rule because voice volume, room acoustics, and the application all change the required gain.
- Turn the Yeti Gain down substantially.
- Set the pickup pattern to Cardioid.
- Place the microphone 4–8 inches from the front of your mouth.
- Speak at the loudest level you expect during a call, stream, or recording.
- Slowly raise Gain until the signal is strong without clipping.
- Move slightly farther away or reduce Gain if laughter, shouting, plosives, or loud consonants distort.
Riverside recommends keeping the physical Gain knob from being raised by more than about one-quarter turn as a conservative starting point, but that position is not a calibration standard for every voice or room. Use the recording or meter to make the final adjustment.
Lower Gain and move closer rather than using high Gain from a distant position whenever the room sounds boomy. High Gain from far away captures more room reflections, keyboard noise, fan noise, and desk vibration. Keep the microphone away from hard walls, avoid placing it directly on a vibrating desk when possible, and use headphones instead of speakers to prevent feedback and acoustic bleed.
Which Blue Yeti pickup pattern should I use?
Cardioid is usually the right choice for one person speaking into the microphone, but the other modes are useful in specific arrangements.
Recommended Free Tools
| Pattern | What it captures | Best use | Why it can sound too loud |
|---|---|---|---|
| Cardioid | Primarily sound from the front | Solo calls, streams, podcasts, and voice recording | Still captures excessive level if Gain or distance is wrong |
| Omnidirectional | Sound from all directions | Group or room sound when broad pickup is intentional | Fan, keyboard, speakers, reflections, and room noise enter readily |
| Bidirectional | Sound from the front and rear | Two people facing opposite sides of the microphone | Captures unwanted rear-room sound for most solo users |
| Stereo | A wider stereo image | Some music or spatial recording setups | Can make the room and side reflections more prominent |
Cardioid often reduces room pickup, but Cardioid does not correct excessive input gain or repair clipping that has already occurred.
How do I lower Blue Yeti input volume in Windows 11?
In Windows 11, use the built-in microphone test to separate a system-level problem from an application-specific problem.
Also popular on Amazon
- Custom three-capsule array: This professional USB gaming mic produces clear, powerful, broadcast-quality sound for YouTube videos, Twitch game streaming, podcasting, Zoom meetings, music recording and more
- Four pickup patterns: Flexible cardioid, omni, bidirectional, and stereo pickup patterns allow you to record in ways that would normally require multiple mics, for vocals, instruments and podcasts
- Blue VO!CE software: Elevate your streamings and recordings with clear broadcast vocal sound and entertain your audience with enhanced effects, advanced modulation and HD audio samples
- Onboard audio controls: This USB microphone offers headphone volume, pattern selection, instant mute, and mic gain to put you in charge of every level of the audio recording and streaming process
- Positionable design: Pivot the mic in relation to the sound source to optimize your sound quality thanks to the adjustable desktop stand and track your voice in real time with no-latency monitoring
- Connect the Yeti directly to the computer during testing.
- Open Start > Settings > System > Sound.
- Under Input, select the Blue Yeti.
- Open the Yeti’s device properties.
- Under Input settings, select Start test.
- Speak normally and at your loudest expected level.
- Select Stop test, then play the sample.
- Lower the Input volume slider if the sample is excessively loud or distorted.
Microsoft documents the Windows microphone test and input-volume path in its microphone setup and testing instructions.
Windows separates several controls that are easy to confuse:
Do these 3 things before closing this tab:
1Clear out junk files and repair common Windows errors2Fix the driver behind crashes, sound loss and screen glitches3Repair Windows errors before they cause bigger problems- Input volume: the strength of the microphone signal entering Windows.
- Application microphone level: how a particular application receives or processes the signal.
- Output volume: how loud playback is through speakers or headphones.
- Yeti headphone volume: monitoring loudness through headphones connected to the microphone.
Lowering speaker volume will not stop a microphone from clipping. Lowering Yeti headphone volume will not necessarily make other people hear your microphone more quietly.
What if the Windows 11 menus look different?
Use the legacy Control Panel path when the modern Settings interface does not expose the required control:
- Open Control Panel.
- Go to Hardware and Sound > Sound.
- Open the Recording tab.
- Select the Blue Yeti and choose Properties.
- Use the Levels tab to reduce the microphone level.
- Open Advanced if one application keeps changing the level.
As a compatibility workaround, you can test with Allow applications to take exclusive control of this device disabled. This is a commonly discussed OBS troubleshooting step, not a guaranteed official fix; the OBS community discussion of app-controlled levels describes the scenario.
Do not blindly disable every Windows enhancement. First test with automatic gain, enhancements, noise suppression, and other processing disabled. Re-enable only the features that solve a demonstrated problem without causing distortion.
Windows Errors? Fix Them Before They Spread
Repair common Windows errors and clear accumulated junk for a smoother, more stable PC - no reinstall needed.Free scan · no reinstallOutdated Drivers Are Slowing You Down
One free scan finds every outdated or missing driver and matches the right update for your exact hardware.Free scan · exact hardware matchHow do I fix a loud Blue Yeti on macOS?
On macOS, select the Yeti as the input device and adjust input level separately from output volume. Newer macOS versions generally use System Settings > Sound; older Logitech documentation may call the same area System Preferences.
- Connect the Yeti directly with the supplied USB cable.
- Open System Settings > Sound.
- Select the Blue Yeti under Input.
- Lower the input level and test normal and loud speech.
- Check the output device separately if only headphone monitoring is too loud.
Logitech’s Yeti setup instructions cover the Mac input and output distinction, although menu wording varies by macOS release.
If an application cannot access the microphone, open System Settings > Privacy & Security > Microphone and allow the application. Select the Blue Yeti explicitly inside the application instead of relying on Default when another microphone is connected. Test in a basic recorder before troubleshooting complex app filters.
Also popular on Amazon
- Custom three-capsule array: This professional USB gaming mic produces clear, powerful, broadcast-quality sound for YouTube videos, Twitch game streaming, podcasting, Zoom meetings, music recording and more
- Four pickup patterns: Flexible cardioid, omni, bidirectional, and stereo pickup patterns allow you to record in ways that would normally require multiple mics, for vocals, instruments and podcasts
- Blue VO!CE software: Elevate your streamings and recordings with clear broadcast vocal sound and entertain your audience with enhanced effects, advanced modulation and HD audio samples
- Onboard audio controls: This USB microphone offers headphone volume, pattern selection, instant mute, and mic gain to put you in charge of every level of the audio recording and streaming process
- Positionable design: Pivot the mic in relation to the sound source to optimize your sound quality thanks to the adjustable desktop stand and track your voice in real time with no-latency monitoring
Why is the Blue Yeti loud only in Discord, Zoom, Teams, or a browser?
A microphone that is clean in the operating-system test but loud in one communication app is usually being changed by that application’s input selection or automatic processing.
- Select the Blue Yeti explicitly as the input device.
- Run the app’s microphone test while speaking normally and loudly.
- Temporarily disable automatic input sensitivity or automatic gain.
- Temporarily disable noise suppression and echo cancellation for diagnosis.
- Set a manual input level that remains clean during loud speech.
- Re-enable processing one feature at a time.
Discord, Zoom, Teams, and browser-based calling tools change their menu names and locations over time, so the exact labels may vary by version. Use the application’s audio or voice settings rather than changing playback volume. If only one app is affected, compare its selected input device and processing with the operating-system test before changing the microphone hardware.
How do I fix a loud or distorted Blue Yeti in OBS?
In OBS, diagnose the raw microphone level before adding filters. Open the Audio Mixer, watch the microphone meter, and speak both normally and at the loudest level expected during a stream.
- Disable all microphone filters temporarily.
- Check whether the unprocessed signal is already too high or distorted.
- Reduce the Yeti Gain or system Input volume if the raw signal clips.
- Use the OBS source or mixer level to balance a clean signal that is merely too prominent in the stream.
- Add processing only after the raw level is safe.
OBS identifies approximately −20 to −9 dBFS as its documented green/yellow operating area and says red begins above −9 dBFS. The OBS audio mixer guidance explains why the meter is more useful than judging loudness from headphones alone.
What OBS filter order should I try?
A sensible beginner diagnostic chain is raw microphone, optional noise suppression, compressor, optional expander or noise gate, and limiter last. The chain is a starting framework, not a universal Blue Yeti preset.
| Filter | Purpose | Use carefully because | Relevant OBS guidance |
|---|---|---|---|
| Noise suppression | Reduces mild fan or room noise | Aggressive suppression can make speech metallic or distorted | OBS Noise Suppression |
| Compressor | Reduces occasional loud peaks | Too much compression can sound flat or can add level through makeup gain | OBS Compressor |
| Expander | Reduces quiet background sound more smoothly than a hard gate | An aggressive threshold can affect quiet speech | OBS Expander |
| Noise gate | Closes the microphone below a threshold | Can cut off the beginnings or ends of words | OBS Noise Gate |
| Limiter | Provides a downstream safety ceiling | Cannot repair clipping that happened before the limiter | OBS Limiter |
OBS documents compressor defaults of a −18 dB threshold and 10:1 ratio, a limiter default threshold of −6 dB, and noise-gate defaults of −32 dB close and −26 dB open. These are software defaults, not calibration values for every Yeti, voice, or room.
For ordinary speech, you can experiment with a compressor threshold around −18 dB and a gentler ratio around 3:1 to 6:1, then use a limiter around −6 dB as protection. Those values are starting points only. OBS’s filters guide recommends placing an expander after compression and before a limiter; listen for cut-off words and pumping instead of copying a preset blindly.
What should I do if the Blue Yeti is loud but not distorted?
If the raw recording is clean, the microphone does not need to be “fixed” at the hardware level. Reduce the application’s source or mixer level when the stream or call mix is too loud, or reduce playback volume when only listening is too loud.
Do not lower the source gain unnecessarily if the signal is healthy and the problem is only the final mix. Conversely, do not use an OBS fader or speaker-volume control to hide clipping that is already present at the microphone input. Adjust the earliest control that is actually overloaded.
Also popular on Amazon
- Custom Three-capsule Array
- Four Pickup Patterns
- Onboard Audio Controls
- Positionable Design
- Plug 'n Play: for Mac or PC
How can I tell whether the Blue Yeti is clipping?
Clipping sounds like crackling, harshness, or a flattened voice on loud syllables, laughter, shouting, and plosive sounds. The meter may reach the top of its scale or red zone, and the distortion remains audible even after playback volume is lowered.
- Lower the Yeti’s rear Gain knob.
- Lower Windows or macOS input volume if necessary.
- Disable application filters and automatic gain temporarily.
- Speak at the loudest level you expect to use.
- Confirm the new recording is clean before adding compression or limiting.
A limiter can protect against some downstream peaks, but a limiter cannot restore detail that clipped at the microphone input or another earlier stage. Lower the level at the earliest point where the meter or recording becomes overloaded.
Could microphone placement make the Yeti sound too loud?
Yes. Placement can make the voice, room, or low-frequency reflections seem excessively strong even when the software level is unchanged.
- Speaking too close increases plosives, bass buildup, and sudden peaks.
- Speaking into the top or rear encourages excessive Gain and produces an uneven result.
- Pointing the microphone toward a hard wall or desk can increase reflections and boominess.
- Placing the microphone directly on a desk can transmit bumps, typing, and vibration.
- Using speakers can feed sound back into the microphone.
- Omnidirectional, Bidirectional, and Stereo modes can capture more unwanted room sound than Cardioid.
Face the front of the microphone toward you, use Cardioid for solo speech, keep your mouth slightly off-axis if plosives are a problem, move the microphone away from reflective surfaces, and use headphones instead of speakers. A boom arm or shock mount may help with positioning and vibration, but neither accessory fixes excessive electronic gain.
Quick wins for a faster PC:
Scan for outdated or missing drivers - takes under a minuteDriver Scan →Clear out junk files and repair common Windows errorsFree Scan →Could USB, sample rate, permissions, or another app be responsible?
USB and software problems are worth isolating after gain, placement, and app settings have been checked. The original Yeti is specified for USB 2.0/3.0 compatibility and 48 kHz/16-bit audio by Logitech.
- Disconnect the Yeti and reconnect it directly to a computer USB port.
- Avoid a hub or monitor connection during diagnosis.
- Try another direct USB port; this is an isolation test, not proof that USB 3 universally causes Yeti problems.
- Try a known-good compatible USB cable.
- Test in the operating system’s built-in microphone recorder.
- Test on another computer if possible.
- Close other audio applications one at a time and check whether launching an app changes the level.
- Compare operating-system and application sample-rate settings, especially where software offers 44.1 kHz or 48 kHz choices.
A sample-rate mismatch can cause instability, unusual behavior, or distortion in some software, although it is not the first explanation for a consistently loud but clean signal. An OBS community troubleshooting report discusses Windows input level, permissions, application control, and 44.1/48 kHz mismatch as possible variables; that discussion is community evidence rather than a manufacturer diagnosis.
Logitech’s current Yeti support page says its Firmware Update Tool is no longer supported or maintained and recommends Logi Options+ for supported devices. Do not download unofficial firmware-reset tools or assume a firmware update will solve ordinary gain or clipping problems.
Independent reader supportYour contribution helps us test, update, and keep practical guides available for everyone.When should I suspect a faulty Blue Yeti?
Suspect the cable, USB connector, or microphone hardware when the same fault persists across multiple computers and applications after conservative gain settings and basic placement checks.
- The signal is distorted at every reasonable Gain setting.
- The same distortion appears in a basic recorder and on another computer.
- Moving or touching the USB cable changes the symptom.
- The microphone intermittently disconnects.
- The USB connector feels loose.
- The Yeti is recognized but produces static or no signal on multiple systems.
- The microphone input and headphone output fail together.
If the Yeti is clean in a basic recorder and only one application is loud, replacement is not the appropriate first step. If a known-good cable, direct USB connection, multiple computers, and multiple recording applications all produce the same severe distortion or static, hardware diagnosis or replacement is reasonable.
Also popular on Amazon
- [Natural Audio Clarity] Operated with frequency response of 50Hz-16KHz, the podcasting XLR mic delivers balanced audio range, likely to resonate with your audience. Directional cardioid dynamic microphone corded will not exaggerate your voice, while rejects unwanted off-axis noise for vocal originality and intelligibility during your PS5 gaming streaming video recording. (Tips: Keep the top of end-addressing XLR dynamic microphone AM8 facing audio source, and suggested recording range is 2 to 6 in.)
- [XLR Connection Upgrade-Ability] To use XLR connection, connect the podcast microphone to an audio interface (or mixer) using a separate XLR cable (NOT Included) . Well-connected and smooth operation improves audio flexibility to make you explore various types of music recording singing. The streaming mic isolates the pristine and accurate sound from ambient noise with greater no interference and fidelity. (RGB and function key on mic are INACTIVE when using XLR connection.)
- [USB Connection with Handy Mute] Skip the hassle of setting something up and plug the cable to play the dynamic USB microphone directly, which suits for beginner creators or daily podcast. You can quickly control the gamer mic with tap-to-mute that is independent of computer/Macbook programs to keep privacy when live streaming. LED mute reminder helps you get rid of forgetting to cancel the mute. (RGB and function key are only available for USB connection, but NOT for XLR connection)
- [Soothing Controllable RGB] RGB ring on the desktop gaming microphone for PC, with 3 modes and more than 10 light colors collection, matches your PC gears accessories for gaming synergy even in dim room. You can control the RGB key button of the dynamic microphone USB directly for game color scheme gaming or live streaming. Configured memory function, the streaming microphone RGB no need to repeated selections after turnning off and brings itself alive when power on. (Only available for USB connection)
- [More Function Keys] Computer microphone with headphones jack upgrades your rhythm game experience and gets feedback whether the real-time voice your audience hear as expected. Get the desired level via monitoring volume control when gaming recording. Smooth mic gain knob on the PC microphone gaming has some resistance to the point, easily for audio attenuation or boost presence to less post-production audio. (Only available for USB connection)
Should I buy an accessory or replace the microphone?
Most loud Blue Yeti problems are setup or signal-chain problems, so adjust the existing microphone before buying another one.
| Situation | Most sensible next step |
|---|---|
| The raw recording is clean but one app is loud | Fix that app’s input selection, automatic gain, filters, or mixer level |
| Headphone monitoring is loud but the recording is fine | Lower Yeti headphone volume or computer output volume |
| Desk bumps or keyboard vibration are the main issue | Consider a boom arm or shock mount |
| Plosives are the main issue | Adjust distance and angle; consider a pop filter or windscreen |
| Speakers bleed into calls or recordings | Use closed-back headphones or reposition the speakers |
| The microphone must be positioned farther from a cramped desk | Consider a boom arm, then retune Gain at the new distance |
| Severe static or distortion persists across systems | Test a known-good cable and consider hardware replacement |
| You want a smaller two-pattern USB microphone | Compare the Yeti Nano, whose official guide specifies Cardioid and Omnidirectional modes, 48 kHz/24-bit operation, and direct computer connection rather than a USB hub |
The Yeti Nano is not a drop-in substitute if you specifically need the original Yeti’s four pickup patterns. A gaming-focused model such as Yeti GX may suit users who want automatic level assistance, but it is a poorer fit for someone who wants the original Yeti’s four-pattern, more manual signal path. Logitech’s official microphone category is the appropriate place to compare current models; prices and availability vary by country and were not included here.
What is the fastest complete fix?
- Set the Yeti to Cardioid and face its front toward you.
- Turn down the rear Gain knob.
- Move to roughly 4–8 inches away and speak at your loudest normal level.
- Use Windows’ or macOS’s basic microphone test before opening the target app.
- Lower the operating-system Input volume if the basic sample is loud or clipped.
- Select the Blue Yeti explicitly inside Discord, Zoom, Teams, OBS, or the browser.
- Disable automatic gain, noise suppression, echo cancellation, and filters temporarily.
- If the raw signal is clean, adjust the application mixer or output level rather than overcorrecting the microphone.
- Add compression or a limiter only after the raw signal is clean.
- Test another USB port, cable, computer, and recorder if the problem remains.
Frequently Asked Questions
Why is my Blue Yeti loud even with the Gain knob turned down?
A Blue Yeti can remain loud when Windows or macOS Input volume, an application level, automatic gain control, compression, or filter makeup gain is also raised. Test the Yeti in a basic recorder, then compare the operating-system level with the affected app.
What’s actually slowing this PC down?
Pick the symptom - the matching free tool is one click away.
Why is my Blue Yeti loud only in Discord?
Discord may be selecting a different input device or applying automatic input sensitivity, gain control, noise suppression, or echo cancellation. Select the Yeti explicitly, run Discord’s microphone test, and temporarily disable automatic processing to isolate the cause.
Why are my Blue Yeti headphones loud when the recording is fine?
The Yeti’s front headphone-volume knob controls monitoring through headphones connected to the microphone. Lower that knob or the computer’s output volume; do not lower microphone Gain unless the recording or call signal is also too loud.
Is Cardioid always the best Blue Yeti pattern?
Cardioid is usually best for one person speaking into the front of the microphone because it reduces pickup from the sides and rear. Bidirectional, Omnidirectional, and Stereo are useful for specific multi-person, room, or spatial recording arrangements.
Do I need to replace my Blue Yeti because it sounds distorted?
Replace the microphone only after testing conservative Gain, a direct USB connection, a known-good cable, a basic recorder, and another computer. Distortion that appears across multiple systems and applications points more strongly to a cable, connector, or microphone hardware problem than to an app setting.
The Bottom Line
The reliable fix for a loud Blue Yeti is to find the first overloaded control: start with the rear Gain knob, then check Windows or macOS Input volume, then the individual application. Use Cardioid and correct side-address placement for solo speech. If the raw recording is clean, fix the app mix or monitoring volume; if the raw recording clips on multiple computers, investigate the cable or microphone hardware.
