The Tool Desk
Outbyte Driver Updater FREEFix the driver behind crashes, sound loss and screen glitchesFind Drivers →Outbyte PC Repair FREERepair Windows errors before they cause bigger problemsFix Now →The PE85N1013 is a 50-ohm coaxial amplified noise-source module covering 10 MHz to 6 GHz. It is specified for wireless bit-error-rate (BER) and noise-figure testing, with -14 dBm output power, -112 dBm/Hz noise power and ±2.5 dB typical flatness. Its RF output is SMA female, and it requires a +15 VDC nominal bias.
What the PE85N1013 does
An amplified noise source generates broadband RF noise for injecting a known noise signal into a test setup. The PE85N1013 is intended for applications including wireless BER and error-rate measurement, noise-figure measurement, automated test equipment (ATE), satellite communications (SATCOM), and radar-related built-in testing. Its stated operating bandwidth is 10 MHz to 6 GHz, making it relevant to systems whose test frequencies fall within that range.
The specifications below are from the PE/Mouser datasheet listing in 2026. They describe the module; they do not establish a particular test result or guarantee compatibility with every test fixture.
PE85N1013 specifications
| Specification | Documented value |
|---|---|
| Frequency range | 10 MHz to 6 GHz |
| Output power | -14 dBm |
| Noise power | -112 dBm/Hz |
| Amplitude flatness | ±2.5 dB typical |
| RF impedance | 50 ohms |
| RF connector | SMA female |
| Bias supply | +15 VDC nominal; 14–18 V range |
| Operating temperature | -40°C to +100°C |
Using it for wireless BER or noise-figure tests
For BER or error-rate work, the module can provide broadband noise to a wireless test setup. The stated frequency coverage must include the band under test, and the output level and noise density must suit the receiver, signal chain and test method. A system may need additional attenuation or other RF conditioning to reach the intended noise level; the published figures alone do not specify a complete calibrated test configuration.
Recommended Free Tools
#1 Best Overall
- Designed as a broadband RF noise for source generator covering 0.001–3000MHz, suitable for spectrum analyzer tracking and RF measurement applications.
- Generates stable white noise signals using for avalanche breakdown noise technology for reliable RF testing performance.
- Supports for spectrum analyzer tracking and signal simulation functions, making it suitable for lab and engineering measurement systems.
- Equipped with for sma output interface and DC12V power input, compatibility with standard RF test setups.
- Built with a stable metal housing structure for durability, long for service and consistent performance in laboratory environments.
For noise-figure measurements, confirm that the measurement method and instrument setup have the calibration information they require. The cited listing does not state an excess-noise-ratio (ENR) calibration status, so do not assume that the module includes a calibration certificate or a specified ENR table.
What to check before selecting a noise source
- Frequency coverage: Ensure the source covers every test frequency of interest; the PE85N1013 is specified from 10 MHz through 6 GHz.
- Level and spectral density: Compare the -14 dBm output power and -112 dBm/Hz noise power with the levels required by the test, accounting for attenuation and the rest of the RF path.
- Flatness: Its ±2.5 dB flatness is typical, not a stated guaranteed maximum across all units or conditions.
- Control range: The listing does not specify an integrated attenuation or output-level control range.
- Connections and power: Check that the SMA female RF interface and 14–18 VDC bias range fit the fixture and supply you plan to use.
- Calibration and environment: Verify calibration or ENR documentation if needed, and make sure the unit’s operating temperature range fits the intended environment.
How it compares with other noise-source options
These are alternatives with different documented features, not interchangeable specifications. Confirm the exact model configuration and current availability with the manufacturer or seller before designing around one.
Rank #2
- [WHITE NOISE OUTPUT] Uses a special voltage regulator tube in breakdown state to generate white noise then amplifies the signal for steady output across 0.001 to 3000MHz for RF testing and bench work.
- [NON LOOPING SIGNAL] This hardware noise source creates continuous electronic noise instead of recorded audio loops helping engineers and hobbyists use it directly as a simple spectrum tracking source.
- [WIDE LEVEL RESPONSE] Built with excellent performance and a high extra noise ratio reference it supports broad frequency coverage with usable strength for spectrum related experiments and signal comparison.
- [POWER AND INTERFACE] Powered by DC12V 0.3A to 1A and supplied with a US plug AC100 to 240V adapter this unit is easy to connect through its SMA output interface for versatile lab integration.
- [MULTI USE DESIGN] Works as a noise generator spectrum tracking source interference source trace generator and block source suitable for engineers hobbyists electronics learning repair benches and RF projects.
| Option | Documented points of comparison | Potential fit |
|---|---|---|
| PE85N1013 | 10 MHz–6 GHz; -14 dBm output power; -112 dBm/Hz noise power; ±2.5 dB typical flatness; 50-ohm path; SMA female output; +15 VDC nominal bias | Broadband wireless BER, noise-figure and related test applications |
| NoiseWave NW6G-M | -14 dBm minimum output and ±2.5 dB flatness; the cited comparison does not state its frequency range, connector, or bias details | A close amplified-module alternative to evaluate; confirm full specifications against your setup |
| SUIN adjustable source | 0–60 dB attenuation adjustable in 0.1 dB steps, with at least 3 dBm output; frequency range and connector are not stated in the cited comparison | Setups where adjustable attenuation and level control are priorities |
| Eravant ST2-011063N10-SF-S1 | 10 MHz–6 GHz white-noise generator; cited for system/component wireless, signal simulation and CATV/HDTV testing; output level and flatness are not stated in the cited comparison | Wireless or video-system noise-generation applications within its stated range |
Finding the exact module
To locate this physical product, search for “PE85N1013 amplified noise source module 10 MHz 6 GHz SMA.” The exact part is documented, but current price, stock and Amazon seller availability have not been established here. Confirm those details and request the complete datasheet before ordering.
Quick Recap
Best Value
- Main Chip is Max2870，Frequency range: 23.5mhz-6000mhz
- Mode: Both Single frequency mode and Sweep mode can be set.
- Automatically save data, support automatic saving after power failure, and automatically execute the previous work function after power on.
- Minimum resolution: 10kHz，Minimum frequency sweep interval: 1ms,Can meet the needs of more high precision.
- Screen: 2.8 inch Touching LCD Screen,Full touch control.
Rank #4
- Premium Quality Material: This Noise Source Tracking is made of brand new and material to ensure a long time use, and the anti-power reverse will also extends it's using time, so you can use this good durability Noise Source Tracking for a long-term
- Excellent Performance : This Simple Spectrum External Tracking Source is designed with low power consumption and low heat to provide an economical use and stable use. at the same time the power supply of the module is DC 9-12V/ 0.15A to provide a stable work condition, and the LED instruction allows you know the relatively data, all of them can provide a better performance
- to Use: This Simple Spectrum External Generator Tracking Source features with a low power consumption and low heat to ensure a stable and use during the working process, no worry about some bad issues caused by over-heated, and the anti-power reverse also helps to create a stable and consistance working environmet for you
- Better than Others: The transistor constant current source to drive the noise diode to produce a wide range of noise sources, and the output noise spectrum of this Noise Source Tracking is more density and more balanced than others, it can obtain a better result with a lower consumption
- Range: The output frequency range is 1.5GHz, the output impedance default is 50 ohms, and it will be the very high level flatness within 0.2M-1.5GHZ
Rank #3
- WIDE for frequency RANGE: White Noise Generator, Covers 0.001 to 3000mhz for precise for spectrum tracking and reliable noise for source testing in various industrial scenarios
- for versatile SIGNAL GENERATION: for spectrum Tracking Generator, Functions as a simple for spectrum tracking tool, trace generator, and block for source to meet diverse measurement needs efficiently
- STABLE PERFORMANCE DESIGN: for Built with metal housing for long lasting for service life and consistent output when used as a critical noise for source device
- EASY POWER CONNECTION: Includes DC12V adapter with for american AC100-240V input and for sma interface for quick setup in your signal conditioning workflow
- PROFESSIONAL TEST SOLUTION: Delivers for accurate white noise generation for engineers requiring a dependable 0.001‑3000mhz for source for complex analysis tasks
Product prices and availability are accurate as of the date/time indicated and are subject to change. Any price and availability information displayed on Amazon at the time of purchase will apply.
