Recommended Free Tools
iTechGuides is reader-supported. When you buy through links on our site, we may earn an affiliate commission. As an Amazon Associate I earn from qualifying purchases. Learn more
You can use a compatible Xfinity remote to control an AV receiver’s volume—and, on some setups, power—after pairing the remote with your Xfinity TV box. On X1, Xumo Stream Box, and Flex, start the Voice Remote’s on-screen setup and opt in when asked about audio receiver control. Then test the receiver’s volume before relying on the setup.
Set up an AV receiver with an Xfinity Voice Remote
On X1, Xumo Stream Box, and Flex, Xfinity’s guided Voice Remote setup handles box pairing first, then TV controls and optional audio receiver controls. Follow the prompts for the devices you actually want the remote to operate.
- Aim the Voice Remote at the Xfinity TV box, press the microphone or Voice button, and say “Program remote.” Follow the on-screen prompts to pair it with that box.
- When asked whether the remote should control TV power and volume, select Yes. Enter the TV brand, select OK, and select OK again when “Ready to pair” appears. Test the TV volume. Select It Works! if it responds; otherwise select It Doesn’t Work and continue through the prompts.
- At the prompt “Do you want to control your audio receiver using your remote?”, select Yes if you want receiver control. Enter the receiver brand and select OK; select OK again at “Ready to pair.”
- Test the receiver’s volume. Confirm It Works! only if the receiver responds.
Xfinity describes receiver control as optional. You do not need to buy a receiver or replace a working remote just to try programming it. See Xfinity’s remote setup instructions.
Find the right code if guided setup fails
If setup does not identify the receiver brand or the test fails, use Xfinity’s Remote Code Lookup and choose the exact remote model before searching. On X1, open Remote Settings to see the remote model; the settings also include TV and Volume Control setup. Xfinity says X1 Remote Setup guides RF pairing and IR programming for TV and audio devices.
#1 Best Overall
- Brand new unopened in plastic bag Xfinity XR15 Remote with voice Control for Xi6, Xi5, XG2 and X1 equipment.
- Enable a voice control for your convieniece in use.
- The Xfinity Voice Remote (models XR15) has an automatic pairing, which will make your installation easy.
- Easy access to accessibility features like Closed Captioning, video description and voice guidance
- The batteries are included in the pack.
Do not assume a TV code will control an AV receiver. Use the code or instructions for the receiver and the exact remote model, then test receiver volume—and power if the instructions support it. Pairing the remote to the TV box alone does not establish that receiver controls are programmed.
Choose instructions for your remote and TV box
Xfinity remote generations do not share one universal button sequence. Use the route for your model rather than transferring a procedure from another remote.
Rank #2
- Noticed: This Remote is New Model XR11 v2-u Designed for Xfinity X1 Platform.
- Aim Anywhere Control (RF Capability): With certain set-top boxes, as well as with HD DTA device.
- Easy access to accessibility features like Closed Captioning and voice guidance.
- Battery Type: 2X1.5V AA Battery , Batteries are not included.
- If you have any questions, please contact us through the amz messaging tool, we promise to help you within 24 hours, thank you!
| Remote or box | Setup route |
|---|---|
| XR16 | No Setup or number buttons: aim at the TV box, say “Program remote” into the microphone, and follow the on-screen flow. |
| XR11 | Use the guided audio receiver flow or code lookup for receiver setup. Xfinity’s separate unlisted-TV fallback is to hold Setup until the light changes from red to green, enter 9-9-1, press Channel Up until the TV turns off, then press Setup to save. That fallback is for an unlisted TV brand, not a substitute receiver code procedure. |
| XR15 | Use the guided flow or code lookup for the receiver. For an unlisted TV, Xfinity documents holding Xfinity and Mute for five seconds until the light changes from red to green, entering the first five-digit code, and testing Power, Volume, and Mute; try the next code if it fails. The support instructions also describe an on-screen three-digit pairing-code route. |
| XR2/XR5 and similar legacy code-based remotes | Xfinity’s older guide says to program the TV first if controlling both TV and AVR, then enter an AVR manufacturer code and test power, volume, and mute. Try another listed code if those controls fail. |
| Legacy TV box | Open Menu → iTV → Self Help → Set Up Remote. Choose the remote model, device type (including audio), and brand, then follow the displayed steps. |
The legacy box route is documented in Xfinity’s remote self-help instructions. The older XR2/XR5 sequence is in Xfinity’s XR2/XR5 guide.
Troubleshoot receiver controls that do not respond
- Check the box pairing. A voice remote is paired with one TV box until it is factory reset. Make sure it is paired with the box you are using.
- Confirm the model before looking up codes. X1 Remote Settings shows the remote model. Select that exact model in Remote Code Lookup.
- Retry the model-specific setup. If a code fails, repeat the applicable setup and try another listed code when that model’s instructions offer one. Verify actual receiver response rather than relying on a successful TV-box pairing.
- Check the batteries. Xfinity notes that replacing batteries can help when remote buttons do not work.
- Reset only as a later remedy. A factory reset erases the TV-box connection, so you must pair the remote again. Reset combinations vary among XR11, XR15, XR16, XR100, and legacy models; follow the instructions for your exact remote rather than borrowing another model’s sequence.
Xfinity’s published material does not establish that every AV receiver is supported or provide a complete receiver compatibility matrix. Check the exact remote and receiver through the current lookup and confirm operation with the receiver itself. If the original remote is missing or broken, Xfinity says a replacement can be obtained at a retail store or mailed through Xfinity Assistant; that is a hardware remedy, not a normal requirement for programming.
Quick Recap
Best Value
- 【Compatible Models】New XR16 Voice Remote Control for Xfinity Comcast TV Box Compatible with Flex Streaming Device Only.
- 【Voice Search Features】Long press the microphone button on the voice remote control and speak your command to easily search for your favorite TV shows, launch applications, etc. on Comcast/Xfinity TV. The voice search function makes navigation a breeze.
- 【Pair the XR16 Remote to Control an Xfinity Flex TV Box】① Point the remote at your TV Box and press the Voice button once. ② Follow the instructions on screen to pair your remote for voice control. ③ Once your remote is paired, follow the on-screen instructions to set up power, volume and input control for your TV. （Note: Please Make sure the TV and Xfinity Flex TV box are turned on and set the TV input to correspond with the Xfinity Flex TV box）
- 【Pair the XR16 Remote to Control a TV or audio device】① Press and hold the Voice button and give the command “program remote“. You can also get there by navigating to the Settings page, then selecting “Remote Settings“ and then “Voice remote pairing.“ ② Follow the instructions on screen to select your TV and audio devices for power, volume, and input control. ③ Aim the remote at the TV, and press the Power button. If the TV turns off, turn the TV back on and verify that the Volume and Mute buttons work.
- 【Perform Factory Reset】Simultaneously press and hold the“ i ”button and the “Home button [house icon] ” until the status light on the remote blinks. This takes about 5 seconds. Press Power, then Last (<- arrow), then Volume Down (-) on your remote in sequence to complete the factory reset. Once this is complete you can retry pairing your XR16 remote.
Rank #4
- Search, change channels, and discover content instantly using voice commands—no typing required. Quickly find shows, apps, or recommendations with a single button press.
- Fully compatible with Xfinity TV boxes, Flex streaming device systems for seamless control of your entertainment setup.
- Use your remote effortlessly in low-light conditions with illuminated buttons and control your TV box without pointing directly at it.
- Access Closed Captioning, voice guidance, and audio description features instantly. Also controls TV power, volume, and input functions.
- Matches original functionality and layout for a seamless user experience. Comes with batteries included so you can set up and start using your remote right out of the box
Rank #3
- Brand new unopened in plastic bag Xfinity XR15 Remote with voice Control
- For Xi6, Xi5, XG2 and X1 equipment
- Voice control
- Batteries included
- Easy access to accessibility features like Closed Captioning, video description and voice guidance
Product prices and availability are accurate as of the date/time indicated and are subject to change. Any price and availability information displayed on Amazon at the time of purchase will apply.
