Free tools Windows power users keep installed
One-click scans. No signup required.
iTechGuides is reader-supported. When you buy through links on our site, we may earn an affiliate commission. As an Amazon Associate I earn from qualifying purchases. Learn more
Recalibrating a Samsung washer means running the calibration routine that is built into your specific model, and the button sequence differs from one family to another. On many US models the sequence is to press and hold Temp. and Delay End together until “Cb” appears, then press Start/Pause. That pattern is common, not universal. Some models need the washer switched on before you enter Calibration mode, some need it off, and some have no calibration mode at all. Your model’s user manual or Samsung’s support page for that exact model should control the steps.
What calibration does
Calibration helps the washer detect the weight of the load more accurately. The washer uses that load-weight reading to decide how much water to add, so an inaccurate reading can lead to a wash that uses too much or too little water. Calibration does not change your wash programs or fix a mechanical fault. It resets the machine’s load-weight detection to a known baseline.
When to run calibration
Samsung recommends calibration in three situations:
- After the washer is installed.
- After you make an adjustment to the appliance.
- When weight detection or the amount of water used seems inaccurate.
Before you start, make sure the washer is in its final position and secured. Calibration done on a machine that is still being moved or leveled can capture a poor baseline.
#1 Best Overall
Before you start
- Remove all laundry and any other items from the drum or tub.
- Confirm the washer is in its intended location and that its feet are secured.
- Find the instructions for your exact model number, which is printed on the rating label inside the door or on the back panel.
A small bubble level can help you check that the washer sits level, which supports stable spinning. It is not part of the calibration procedure, and Samsung’s steps do not list it. Samsung’s spin troubleshooting does discuss adjusting the washer legs for stability, so use the level only as a setup check.
Find the procedure for your model
Samsung’s documented procedures differ by model family. The table below shows the variables that change the steps. Use your manual to fill in the details for your own machine.
Rank #2
- Exclusive Installation Bundle: Includes 3-Prong and 4-Prong Dryer Power Cords, Washer Hose Set, 8-ft Vent Duct, and 1-Year CPS Protection Plan
- Smart Wi-Fi Enabled: Control washer and dryer remotely via SmartThings app
- 4.7 cu ft capacity Washer with Active WaterJet & vibration reduction tech
- Built-in WaterJet faucet lets you pretreat stains inside the tub
- Self Clean keeps the tub fresh without harsh chemicals
| Model family (as documented) | Starting power state | Button sequence | Start control | What you should see |
|---|---|---|---|---|
| Front-load, WF50BG83 family (suffix letters vary) | Not stated in the cited instructions for this family | Temp. + Delay End until “Cb” appears | Hold Start/Pause, as the cited instructions describe | Drum rotates back and forth; door locks during the operation |
| Top-load, WA52M7750A and WA52M7755A families | Washer powered on | Temp. + Delay End | Press Start/Pause | Pulsator rotates for about one minute, then “End” appears |
| Models with FlexWash upper and lower washers or navigation-dial panels | Varies; see the model’s manual | Settings or dial-based navigation, not the same buttons | Varies; see the model’s manual | Varies; see the model’s manual |
| Models without a calibration mode | Not applicable | Not applicable | Not applicable | Samsung states that if the manual gives no calibration instructions, the model does not have this feature |
General steps, where your model supports calibration
- Remove all laundry and other contents from the washer.
- Look up the instructions for your exact model. Check whether the washer should be on or off when you enter Calibration mode, and confirm the button combination.
- On many US models, press and hold Temp. and Delay End together for about three seconds until “Cb” appears. If your model needs a different starting power state, set that first.
- Press Start/Pause to begin. The tub or drum rotates back and forth. On front-load models the door may lock during the cycle, so do not force it open.
- Wait for the completion cue. Samsung’s general US troubleshooting guidance lists “En,” “End,” or “0.” Some models turn off automatically when finished.
Samsung describes the usual calibration duration as one to three minutes. This is the company’s procedure-duration range, not a measured study result, and the time you see on your machine may differ.
Recommended Free Tools
Model examples
Front-load WF50BG83 family
The cited instructions for this family use Temp. + Delay End to enter the mode, a hold of Start/Pause to run it, and a locked door during the operation. These steps apply to the WF50BG83 family only. Model suffix letters vary, so confirm that your machine’s model number matches.
Rank #3
- Exclusive Installation Bundle: Includes 3-Prong and 4-Prong Dryer Power Cords, Washer Hose Set, 8-ft Vent Duct, and 1-Year CPS Protection Plan
- Smart Wi-Fi Enabled: Control washer and dryer remotely via SmartThings app
- 4.4 cu ft capacity Washer with Active & vibration reduction tech
- Easy to Use and Navigate
- Self Clean keeps the tub fresh without harsh chemicals
Top-load WA52M7750A and WA52M7755A families
The cited instructions for these models use Temp. + Delay End while the washer is powered on, then a single press of Start/Pause. The pulsator rotates for about one minute, and “End” appears when the procedure is complete.
Models with alternate panels
Samsung’s regional support pages also describe panels that use a navigation dial, a Settings menu, or separate controls for FlexWash upper and lower washers. Those models do not follow the Temp. + Delay End pattern in the same way. Do not try button combinations at random on these panels. Identify the model, then follow its manual.
Independent reader supportYour contribution helps us test, update, and keep practical guides available for everyone.If calibration will not start
If the tub or drum does not rotate when you start calibration, stop and contact Samsung support to arrange service. Do not treat a calibration that never started, or one that was interrupted before a completion cue, as successful.
Crashes, No Sound, or Screen Glitches?
Random freezes, missing sound and display glitches usually trace back to one bad driver. Find and replace yours safely.Free scan · under a minutePC Slower Than It Used to Be?
A free scan shows the junk files, broken settings and background clutter dragging Windows down - then fixes them in one click.Free scan · Windows 10 & 11If the washer uses too much water
Calibration is a reasonable first check when your washer seems to over-fill for the load size, because the water amount depends on the load-weight reading. Run calibration only after you have confirmed the load is empty and the machine is positioned correctly. If the washer still uses too much water after a successful calibration, the cause may be a water-fill or sensor fault that needs model-specific troubleshooting, and that falls outside what calibration can fix.
Sources
These steps are drawn from Samsung US Support pages and installation instructions for the models named above. Samsung revises its support content and model documentation over time, so compare what you see on your washer with the current manual for your exact model before you rely on any step.
Samsung US Support, installation instructions, quoting the company’s own wording: “Some models don’t have a Calibration mode, so if the manual doesn’t give instructions, then the model doesn’t have it.”
Quick Recap
Product prices and availability are accurate as of the date/time indicated and are subject to change. Any price and availability information displayed on Amazon at the time of purchase will apply.
