iTechGuides is reader-supported. When you buy through links on our site, we may earn an affiliate commission. As an Amazon Associate I earn from qualifying purchases. Learn more
Choose a data-center power distribution system by mapping the complete path from utility service to each IT load, then matching the architecture to present and planned kilowatts, voltage and phase, redundancy, room layout, change rate, monitoring, safety, and lifecycle cost. A rack PDU is only the final distribution device at the cabinet; it cannot generate, condition, or back up power. Most facilities compare a conventional floor-PDU/remote-power-panel (RPP) design with busway, while higher-voltage AC and DC options require additional engineering. The right answer is the topology that your electrical engineer can protect, maintain, expand, and operate safely for the actual site—not a universally “best” product.
Start with the entire power path, not a rack accessory
Before selecting any PDU, draw the one-line path that serves the IT load. A typical chain is utility service, service switchgear, generator plant, automatic transfer equipment, UPS system, downstream switchboards or floor PDUs, branch circuits or busway tap-off units, rack PDUs, and finally servers, storage, and network equipment. During a utility outage, the UPS supports the load while the generator starts and the transfer sequence completes. The floor-level equipment then distributes the available power to rows, and the rack PDU delivers it to equipment cords.
This distinction matters because a rack PDU only distributes power that is already available. It does not provide UPS autonomy, generator capacity, short-circuit protection for the whole room, or a second independent path. Vertiv’s 2019 rack-PDU guidance treats the rack unit as the last link to IT equipment, while a floor PDU is an upstream distribution assembly. Confusing the two can leave a design with excellent cabinet metering but insufficient upstream capacity or no maintainable redundant path.
Make the one-line drawing the controlling document. Mark normal and alternate sources, isolation points, protective devices, transformers, neutral conductors, grounding connections, and every point where maintenance can interrupt a load. Have the responsible electrical engineer verify fault-current levels, selective coordination, arc-flash labeling, working clearances, and the authority having jurisdiction’s requirements.
#1 Best Overall
- RACK MOUNTABLE: This 1U Rackmount PDU power strip fits 19" standard server racks and cabinets, featuring a 1U horizontal rack mount form factor that ensures compatibility with all 19" server racks.
- 15A Overload Protection Switch: Provides overload protection by interrupting the circuit when the load exceeds the rated current.
- HEAVY-DUTY: The power distribution unit features a heavy-duty construction, meticulously designed with robust components and housed in a durable aluminum alloy casing, ensuring a sturdy and long-lasting performance for reliable power management.
- POWER CORD: The power distribution unit comes equipped with a 6-foot (1.8 meter) 14AWG power cord, providing flexible placement options and extended reach for versatile installation in various settings.
- Commitment: ElecVoztile is dedicated to delivering superior products and outstanding customer service. Should you encounter any issues, please do not hesitate to reach out to us for immediate assistance.
Collect the requirements that determine the architecture
A useful comparison starts with a written load and operations brief. Do not ask only, “What power rating does the rack PDU have?” Capture the following inputs for each room, row, and cabinet.
Installed and planned load
- Record the nameplate and measured demand of installed servers, storage, network, and specialist equipment.
- Separate continuous IT demand from temporary startup or inrush demand where the equipment documentation requires it.
- Document the expected rack-by-rack growth, new rows, and replacement cycles. Vertiv advises estimating the kilowatts required by installed equipment and considering anticipated growth before choosing an rPDU.
- State whether the design limit is based on breaker rating, cooling capacity, UPS capacity, floor loading, or another constraint. The smallest constraint governs practical deployment.
Electrical characteristics
- Identify the available voltage, frequency, and number of phases at the intended distribution point.
- Specify the allowable current per circuit and the connection method: hardwired input, pin-and-sleeve connector, or another approved connector.
- List the outlet types and counts required by the actual IT cords, including any locking or retention requirement.
- Define neutral and grounding arrangements, transformer connections, and the protection scheme rather than assuming a rack unit can correct an upstream mismatch.
Redundancy and availability
State whether each cabinet has one source, A and B sources, or a more complex concurrently maintainable arrangement. A dual-corded server normally receives one cord from each path, but that only improves availability if the paths are genuinely independent upstream. Identify which breakers, busway sections, tap-off boxes, UPS modules, generators, and maintenance bypasses can be isolated without dropping the intended loads. Do not label a system “Tier” or assign a reliability level without the project’s formal design criteria and review.
Room and routing constraints
- Measure raised-floor depth, ceiling height, overhead obstructions, aisle widths, and equipment clearances.
- Map cable routes, fire-rated penetrations, seismic restraints, and access needed to add or replace circuits.
- Record rack positions that may move and the maximum distance from the distribution source.
- Check whether the building can support the weight, heat rejection, and maintenance access of transformers, switchboards, or busway sections.
Operational requirements
Decide how much visibility and control the operations team needs. A basic unit may be sufficient when upstream metering is adequate and no outlet-level action is required. Metered or monitored rPDUs provide local or network visibility into current, power, energy, phase balance, or alarms, depending on the model. Switched rPDUs add remote outlet control, which can help with controlled reboot procedures but also introduces authentication, network, and change-management requirements. Vertiv’s buying guidance distinguishes basic, metered, monitored, and switched categories; exact functions vary by model.
Outdated Drivers Are Slowing You Down
One free scan finds every outdated or missing driver and matches the right update for your exact hardware.Free scan · exact hardware matchWindows Errors? Fix Them Before They Spread
Repair common Windows errors and clear accumulated junk for a smoother, more stable PC - no reinstall needed.Free scan · no reinstallCompare the two common facility architectures
Most low-voltage data-center designs fall into a conventional floor-PDU/RPP approach, a busway approach, or a combination. Schneider Electric’s technical material describes the core components of both. The choice should be made against the load profile and room operations, not by treating one as universally superior.
| Decision factor | Floor PDU and RPP distribution | Busway distribution |
|---|---|---|
| Basic arrangement | Upstream PDU assemblies, panelboards or remote power panels, and branch cables run to rack locations. | An upstream low-voltage feed supplies a bus; protected plug-in or tap-off units provide branch circuits near the racks. |
| Physical placement | Equipment may be in electrical rooms, at the floor edge, or distributed through the raised-floor area, with cables routed to cabinets. | Busway can be installed overhead, underfloor, or vertically, subject to structural, clearance, and access requirements. |
| Change method | Adding or moving capacity can require new breakers, cable pulls, penetrations, and work in occupied pathways. | Approved tap-off units can make branch additions or moves modular, but the bus and tap-off system must be rated and coordinated for the intended use. |
| Layout fit | Works well where cable pathways and panel locations are stable and already planned. | Can suit frequently changing rows or high-density areas where a nearby bus reduces long branch-cable runs. |
| Maintenance | Isolation points and spare breakers are planned in panels and PDUs; service work may affect a larger cable group. | Sections, tap-offs, and upstream equipment need an isolation and maintenance strategy; access and energized-work rules are critical. |
| Cost evidence | Project cost depends on equipment, transformer and panel count, cabling, labor, and future changes; no neutral quantified comparison is established here. | Project cost depends on bus length, supports, tap-offs, protection, installation, and future changes; no neutral quantified comparison is established here. |
Vertiv’s white paper characterizes traditional transformer-based distribution as potentially space-intensive and slower to change, and presents busway as a modular alternative, particularly for high-density applications. Those are vendor-authored architecture claims, not a guarantee for every building. Schneider Electric independently describes the components and configurations, but the final selection still depends on local code, available fault current, labor, and operating practice.
When a floor PDU or remote power panel is the better fit
A conventional design groups distribution equipment into floor PDUs, remote power panels, or both. Schneider Electric describes traditional PDUs as assemblies that can include an input breaker, panelboards, transformers, output cables, surge arrestors, and monitoring or communications. An RPP is principally a panelboard-based distribution point that places branch protection closer to the load.
Strengths to evaluate
- Existing buildings may already have electrical rooms, raised-floor routes, and panelboard practices that the team understands.
- Branch circuits, breaker positions, and cable schedules are familiar to electricians and facility operators.
- Transformers can provide the voltage conversion required by the IT equipment, with the neutral and grounding scheme designed as part of the assembly.
- Equipment can be segregated by source or redundancy path using separate panels and cable routes.
Questions that expose limitations
- How many new circuits can the panels accept without replacing equipment?
- Will future cable pulls compete with cooling, fire protection, or network pathways?
- Does a row move require de-energizing a panel or opening a floor?
- Are transformer heat, sound, floor loading, and maintenance clearances acceptable?
- Can the design preserve A/B independence all the way to the rack?
Conventional distribution is not automatically inflexible. Spare capacity, distributed RPPs, well-planned pathways, and clear circuit identification can make it practical. Its weakness appears when the original layout assumptions change faster than the cable and panel infrastructure can be modified.
Do these 3 things before closing this tab:
1Scan for outdated or missing drivers - takes under a minute2Repair Windows errors before they cause bigger problems3Fix the driver behind crashes, sound loss and screen glitchesRank #2
- CONVENIENT LAYOUT: This rack-mount 16-outlet (120V) NEMA 5-15 power strip features a steel chassis, 6 ports on the front, and 10 ports on the back, so you can easily plug devices in and manage cables
- SCALABLE: This 1U rack mount PDU is ideal for small rack setups with only a few devices, allowing for plenty of future expansion, and features a 6 ft long cord so you can move your rack around
- EASY INSTALLATION: This rackmount PDU supports 19 inch rack 1U horizontal installation; Features LED indicators for ground and surge detection, a built-in circuit breaker, surge protection, and meets ANSI/EIA RS-310-D standards
- BROAD COMPATIBILITY: 1U horizontal rack-mounted power distribution unit fits many network / data 2-post and 4-post racks; Compatible with 19" server racks with minium 4" (10.2cm) depth
- THE IT PRO'S CHOICE: Designed and built for IT Professionals, this rack PDU is backed for 2-Years, including free lifetime 24/5 multi-lingual technical assistance
When busway deserves serious consideration
Busway uses an upstream feed, a bus assembly, and protected tap-off units that plug into approved points along the run. The bus can be overhead, underfloor, or vertical. A tap-off then supplies a branch circuit or rack PDU. This arrangement moves much of the change activity from pulling long cables to installing, relocating, or replacing listed tap-off units.
Evaluate busway against the room
- Confirm that the ceiling structure, seismic design, and service clearances can support the busway route.
- Check that overhead busway does not conflict with ducts, sprinklers, cable trays, lighting, or crane paths.
- For underfloor installations, verify raised-floor depth, water exposure, access, and separation from data cabling.
- Define how tap-offs are locked, labeled, interlocked, inspected, and removed under the site’s energized-work policy.
- Confirm that every tap-off’s breaker rating, phase arrangement, connector, and enclosure match the rack PDU and the upstream coordination study.
Busway can reduce the physical disruption of adding rack capacity, but it does not eliminate engineering. The bus still needs correct short-circuit ratings, overcurrent protection, grounding, thermal limits, and maintenance isolation. A modular tap-off is not permission to connect arbitrary loads or to work energized without an approved procedure.
Choose the voltage and phase strategy deliberately
Voltage and phase decisions flow from the utility service, UPS output, transformer arrangement, IT equipment ratings, and local standards. A rack PDU cannot make an incompatible source safe. Obtain the nameplate range for every intended load and confirm that the proposed receptacle voltage, phase, frequency, and neutral arrangement are accepted by the equipment manufacturer.
Single-phase and three-phase distribution
Single-phase rack circuits are common at the cabinet, while three-phase distribution can move more power through upstream equipment and may support better phase balancing. The practical choice depends on the facility’s source, breaker poles, connector standards, rack density, and the mix of single- and three-phase loads. Ask whether the selected rPDU can distribute the required phase arrangement without leaving unusable capacity or creating an imbalance that the upstream design cannot tolerate.
Recommended Free Tools
415 V four-wire designs
Vertiv’s July 2026 guidance presents 415 V four-wire distribution as a way to deliver 240 V single-phase power to racks with fewer downstream conversion stages. This topology is not a plug-in upgrade. The UPS must be engineered to manage the neutral conductor, and the design must address phase regulation, monitoring and control, fault protection, and applicable standards. Confirm that every downstream device—including busway tap-offs, rack PDUs, maintenance equipment, and test instruments—is rated for the selected system. Treat the approach as vendor guidance for an engineered project, not evidence that it suits every site.
Direct-current architectures
DC distribution can be attractive in specific designs, but it changes the protection and maintenance problem rather than merely changing the voltage. Uptime Institute’s September 2026 briefing notes that DC current does not naturally pass through zero, so interruption behavior differs from AC. Converter, battery, capacitor, and protective-device characteristics affect fault detection and clearing. The briefing also identifies grounding, stored energy, worker safety, and the difficulty of providing a maintenance bypass as distinct concerns.
Use DC only with equipment and protection specifically engineered for that system. The design package should define fault interruption, arc-flash and shock boundaries, detection, isolation, grounding, battery and capacitor discharge, labeling, test procedures, and emergency response. Electrical installation and maintenance require qualified personnel and site-specific procedures.
Rank #3
- 1U 8-OUTLET RACK MOUNT PDU: Built-in 8ft. (2.4m) NEMA 5-15P Power Cord; 8x NEMA 5-15R Outlets; 125V Max. Input/Output; 15A Circuit Breaker; Ideal power supply for server rooms, server closets, small data centers and recording studios
- ON/OFF OUTLET SWITCHES: Each outlet features an individual illuminated rocker switch for controlled power management; Enumerated switch labels clearly identify the corresponding outlet; Safety covers prevent accidental power cycling
- 15 AMP CIRCUIT BREAKER: This 8-port rackmount power distribution unit features a self-tripping and resettable circuit breaker with 15A trip-point to protect connected equipment
- 1U RACK DESIGN: This horizontal power distribution unit installs in 1U of rack space on network racks and is compatible with all 19-inch server racks 4" or deeper; Compatible with ANSI/EIA RS-310-D standards
- OPTIMIZED DESIGN: Heavy-duty steel housing with rear facing outlets; Attached 8 ft. (2.4m) long power cord
Specify the rack PDU after the upstream design is fixed
Once the facility distribution point is known, create an rPDU specification for each rack class. Vertiv recommends starting with approximate kilowatts and growth, then matching phase, amperage, voltage, and connection requirements. Use a schedule rather than selecting a generic “high-power” unit.
Quick wins for a faster PC:
Clear out junk files and repair common Windows errorsFree Scan →Fix the driver behind crashes, sound loss and screen glitchesFind Drivers →Repair Windows errors before they cause bigger problemsFix Now →| Specification | What to record | Why it matters |
|---|---|---|
| Input power | Voltage, frequency, phase, maximum current, connector or hardwire method, and cord length. | Must match the branch circuit, tap-off, breaker, and source topology. |
| Output | Outlet types, quantity, spacing, retention, and any locking requirement. | Must accept the installed equipment cords without unsafe adapters or overloaded receptacles. |
| Capacity | Required present load, planned growth, and the applicable continuous-load limit established by the engineer. | Prevents nuisance trips and avoids buying a unit that is full on day one. |
| Form factor | Vertical 0U, horizontal rack-mount, or another approved mounting method. | Determines rack-unit consumption, cable access, airflow clearance, and serviceability. |
| Monitoring | Basic, local metered, network monitored, phase-level, outlet-level, alarms, and energy reporting as required. | Aligns visibility with staffing and capacity-management practice. |
| Switching | Whether individual or grouped outlets can be remotely switched, and the authorization model. | Remote control can aid recovery but creates operational and cybersecurity dependencies. |
| Environment | Temperature, humidity, ingress, seismic, and enclosure requirements for the room. | Ensures the unit is suitable for its actual installation location. |
Horizontal versus vertical mounting
A horizontal unit occupies rack units and may be convenient where cabinet height is available. A vertical 0U unit preserves rack space but requires side clearance and a compatible mounting location. Confirm door swing, cable bend radius, airflow, and whether the chosen position blocks adjacent equipment or a second power path.
Basic, metered, monitored, or switched
- Basic: distributes power with no additional measurement or remote outlet control beyond any upstream instrumentation.
- Metered: displays electrical values locally; the exact measurements depend on the model.
- Monitored: communicates measurements and alarms to a management system, subject to network and protocol support.
- Switched: adds remote outlet management, which must be governed by authentication, authorization, change control, and recovery procedures.
Do not assume a monitored unit measures every outlet or that a switched unit can safely cycle any device. Review the model’s measurement points, alarm thresholds, firmware support, fail behavior, network isolation, and reset procedure with operations and security teams.
Design redundancy that survives a real failure
Redundancy is a property of the path, not a label on the rack PDU. For an A/B cabinet, trace source A and source B through utility or generator switchgear, UPS modules, distribution panels or busway, tap-offs, and rPDUs. Look for shared breakers, shared maintenance bypasses, common cable trays, common control networks, and single rooms that can defeat the intended independence.
Define what may be maintained while the load remains online. A design that has two feeds but requires both to be removed for a busway inspection is not equivalent to one with truly isolated maintainable sections. Document normal operating positions, transfer sequences, breaker interlocks, and restoration steps. Test the procedure under controlled conditions; do not infer performance from the single-line drawing alone.
The Tool Desk
Outbyte Driver Updater FREEScan for outdated or missing drivers - takes under a minuteDriver Scan →Outbyte PC Repair FREEClear out junk files and repair common Windows errorsFree Scan →Use monitoring and control as an operating decision
Metering supports capacity planning, phase balancing, alarm response, and evidence that a circuit is approaching its engineered limit. Determine the needed granularity: room, panel, bus section, tap-off, rack, phase, or outlet. More measurement points increase integration and maintenance work, so instrument where the team can act on the data.
For networked rPDUs, place management interfaces in an appropriately segmented operations network. Define account ownership, multifactor or equivalent controls where supported, firmware governance, logging, time synchronization, and behavior during loss of network connectivity. If remote switching is enabled, require a documented approval and a local recovery method. A switched outlet that is inaccessible after a network or authentication failure can turn a convenience feature into an outage risk.
Rank #4
- Rack mount 9-outlet power distribution unit (PDU) designed for standard 19-inch server racks, ideal for data centers, server rooms, and network closets
- Wide spacing for 2 outlets to accommodate larger plugs and adapters, improving cable management and reducing outlet overcrowding
- Individual on/off switches for each outlet, allowing convenient and independent control of connected devices
- 1u PDU includes 2 high-speed USB fast charging ports and 2 type C ports for simultaneous power supply and device charging
- Built-in overloading protection safeguards connected equipment from power surges and overloads, ensuring safe, reliable operation
Compare lifecycle cost instead of purchase price
A neutral total-cost number is not established for these architectures, so build a project-specific model. Include:
- Switchboards, transformers, floor PDUs, RPPs, busway, tap-offs, rPDUs, breakers, and protective devices.
- Engineering studies, permits, structural supports, fire stopping, commissioning, and acceptance testing.
- Installation labor, cable and connector quantities, lifting, outage windows, and temporary power.
- Future circuit additions, rack moves, spare equipment, and the labor needed to label and document changes.
- Energy and cooling effects of conversion equipment, where measured for the actual design rather than assumed from a marketing claim.
- Maintenance access, replacement lead times, training, monitoring integration, and the cost of an interruption during change work.
Vertiv presents busway as more modular and flexible than some traditional transformer-based arrangements, while traditional systems may be familiar and readily supported by existing facilities staff. Those trade-offs should be tested against your own change frequency, labor rates, room constraints, and outage costs. Do not use an unverified percentage saving or density figure as a design input.
A practical selection workflow
- Draw the one-line path. Show utility, generators, transfer equipment, UPS, switchboards, floor distribution or busway, branch protection, rPDUs, and IT loads.
- Build the load schedule. Record measured and nameplate demand, rack-by-rack growth, startup behavior, and the limiting capacity at each upstream stage.
- Define availability. Specify A/B requirements, maintenance windows, isolation points, and the failure scenarios the design must withstand.
- Survey the room. Capture floor and ceiling constraints, routes, structural support, clearances, fire penetrations, and rack move patterns.
- Short-list architectures. Compare floor PDU/RPP, busway, or a hybrid against density, changeability, protection, operations, and lifecycle cost.
- Confirm electrical compatibility. Have the engineer verify voltage, phase, neutral, grounding, fault levels, breaker coordination, arc-flash analysis, and equipment ratings.
- Choose monitoring and control. Select the minimum useful granularity and define network, security, alarm, and remote-switching policies.
- Write the rack-PDU schedule. For every rack class, list input connector, voltage, phase, current, outlets, mounting, monitoring, switching, environmental rating, and spare strategy.
- Review maintainability. Walk through adding a circuit, replacing a tap-off or rPDU, isolating a fault, and servicing each source without an unintended outage.
- Commission and document. Test transfers, alarms, metering, breaker labeling, interlocks, and failover procedures; deliver updated one-lines, schedules, settings, and operating instructions.
Common mistakes and how to correct them
Buying the rack PDU first
Symptom: the selected unit has the wrong connector, phase, or voltage for the branch circuit. Correction: freeze the upstream electrical design and rack schedule before ordering cabinet equipment.
Counting nameplate watts without a growth or protection review
Symptom: breakers trip when new servers are installed even though the arithmetic looked adequate. Correction: include planned growth, continuous-load rules, startup behavior, phase balance, and the engineer’s coordination study.
Calling two cords “redundant” when both paths share a failure point
Symptom: one panel, UPS bypass, bus section, or cable route can remove both feeds. Correction: trace and document source independence, then test the maintenance and failure procedures.
Assuming busway is maintenance-free
Symptom: tap-offs are inaccessible, unlabeled, or incompatible with the protection study. Correction: provide clear access, locking and labeling rules, spare strategy, approved work procedures, and coordinated ratings.
Adding remote switching without governance
Symptom: an operator cycles the wrong outlet or loses access after a network change. Correction: enforce role-based access, change approval, logging, local recovery, and device-specific reset instructions.
Best Value
- Efficient Power Distribution: Delivers 12A (US Listed 12A) power through 8 NEMA 5-15R ports, ideal for server racks, network setups, and office environments
- Comprehensive Indicators: Monitors status with Power (yellow), Earth (green), and Lightning Protection (red) indicators, ensuring secure power for server rooms and warehouses
- Compact Design: Sleek 1U horizontal profile (19" x 1.7" x 1.7") maximizes rack space efficiency in IT cabinets
- Versatile Compatibility: 1 NEMA 5-15P input for seamless integration in diverse setups, providing flexibility for network installations
- Safety Assurance: UL listed for compliance, guaranteeing safety and quality in data centers and office spaces
Adopting DC or 415 V as a trend purchase
Symptom: protection devices, neutral management, maintenance bypass, or worker procedures are unresolved. Correction: require a complete engineered design, applicable-standard review, equipment compatibility evidence, and qualified commissioning before deployment.
Decision examples
Stable rows in an existing facility
If rack positions change rarely, the building already has usable electrical rooms and raised-floor pathways, and staff are experienced with panelboards, a floor PDU/RPP design may minimize disruption. Reserve panel space and cable routes for documented growth, and keep A/B paths physically and electrically distinct.
Frequently changing, high-density rows
If deployments move often and the room can support overhead infrastructure, busway with coordinated tap-offs may reduce the work involved in relocating branch circuits. Validate structural support, clearances, tap-off access, and energized-work controls before selecting it.
What’s actually slowing this PC down?
Pick the symptom - the matching free tool is one click away.
Mixed-density expansion
A hybrid can place busway in rapidly changing high-density zones while retaining conventional panels for stable areas or specialty loads. The hybrid still needs one coordinated protection, grounding, labeling, monitoring, and maintenance strategy; separate subsystems must not create ambiguous operating boundaries.
Considering 415 V or DC
Treat either option as a project-level electrical architecture change. Confirm source and UPS behavior, neutral or grounding design, protective-device interruption, equipment ratings, worker training, maintenance bypass, and applicable standards before comparing any rack hardware.
What a complete specification package should contain
- Approved one-line diagrams showing normal, alternate, bypass, and maintenance states.
- Load schedules with present demand, growth assumptions, rack limits, and source assignments.
- Short-circuit, selective-coordination, arc-flash, grounding, and protection studies as required by the jurisdiction and design criteria.
- Room layouts showing racks, floor PDUs or busway, tap-offs, panels, cable routes, clearances, and access zones.
- Rack-PDU schedules with input and output details, mounting, monitoring, switching, and environmental requirements.
- Method statements for installation, testing, energization, transfer, isolation, and emergency response.
- Operations documentation covering alarms, remote control, labeling, spare parts, firmware, and change approval.
The final selection should be approved by the project’s qualified electrical engineer and operations authority. Site utility characteristics, jurisdiction, fault levels, reliability objectives, layout, and applicable standards were not established for this general guide, so no specific topology, voltage, breaker setting, redundancy tier, or product model can be prescribed safely without that information.
Quick Recap
Product prices and availability are accurate as of the date/time indicated and are subject to change. Any price and availability information displayed on Amazon at the time of purchase will apply.
Free tools Windows power users keep installed
One-click scans. No signup required.
